Display LED modelo de cartão de recepção A5

Features

Description

Supporting pixel level brightness and chroma calibration

Working with NovaLCT and NovaCLB, A5 supports brightness and chroma calibration on each pixel.

Supporting image rotation in 90° increments

(Calibration not supported after rotation)

On NovaLCT, the image on the screen can be set to rotate in the multiples of 90° (90°, 180°, 270° and 360°).

Supporting quick seam correction

Working with NovaLCT, A5 supports quick adjustment of bright and dark lines, which can remove the seams between modules and between cabinets.

Supporting 3D function

On NovaLCT or operation panel of controllers which support 3D function, you can enable 3D function and set the 3D parameters to make the LED screen display 3D effects.

Features

Description

Supporting the smart module

(Supported by dedicated firmware program)

The smart module is composed of Flash and MCU.

Flash could store calibration coefficients and module information. MCU could communicate with the receiving card to realize monitoring over temperature, voltage and wiring communication status for the module. Working with the driver chip, A5 supports open circuit detection on LED.

The smart module could make monitoring unit smaller, requiring no independent monitoring card

Features

Description

and saving cabinet space.

Supporting LVDS transmission

(Supported by dedicated firmware program)

The transmission mode of low-voltage differential signaling (LVDS) is used, which reduces the number of data cables that connect the receiving card's HUB board to the module, increases the transmission distance, improves the signal transmission quality, and better stabilizes the image output.

Supporting auto module calibration

After the module has been replaced, the receiving card can automatically read the new module ID and calibration coefficient which could be saved to calibration system files.

Supporting Mapping function

Enable the Mapping function on NovaLCT, then the target cabinet will display the cabinet number and Ethernet port information, and the user could get the receiving card`s location and wiring route.

Supporting setting of images pre-stored of the receiving card

On NovaLCT, the specified images could be set as the screen startup image and images used when the Ethernet cable is disconnected or no video source signal is available.

Supporting module Flash management

On NovaLCT, lamp panel Flash could be managed.

Supporting monitoring voltage and temperature of itself

The voltage and temperature of the receiving card itself can be monitored without using other peripherals. The monitoring data can be checked on NovaLCT.

Supporting LCD module

Supports NovaStar's general 5-pin LCD module. The LCD module is connected to the HUB board to display temperature, voltage, single operating time and total operating time of the receiving card.

Support one-click application of calibration coefficient in module Flash

In the event of network outage, hold down the self- test button to read the calibration coefficient in module Flash back to the receiving card.

Features

Description

Supporting dual-card backup

In the high-reliability environment, single HUB board could be populated with two A5 receiving cards. In case that the main receiving card fails, the standby one will serve in a timely manner to ensure normal operation of the display.

Supporting dual-power

Two power supplies could be simultaneously

Features

Description

backup detection

connected, and operating status of the power supplies could be detected.

Supporting loop backup

HUB`s Ethernet port improves the reliability for the serial connection of the receiving card through main and standby redundant mechanism. Among the main and standby serial connection lines, if one fails, the other will begin to work to ensure the normal operation of the display.

Features

Description

Supporting readback of firmware version

On NovaLCT, the firmware versions of the receiving card can be read back.

Supporting dual-backup and restoring of the calibration coefficient

Calibration coefficients could be saved to both the factory area and application area at the same time.

Calibration coefficients in the factory area is default as the delivery value, while the calibration coefficient in the application area could be modified or be restored to the factory reset by the user on NovaLCT.

Supporting readback of configuration file

• l  On NovaLCT, the receiving card configuration parameters can be backed up to the receiving card.
• l  On NovaLCT, the receiving card configuration parameters can be read back.